F 45 ELMO IV:
High-level CNC-technology.

The F 45 ELMO IV is the pinnacle of the Altendorf sliding table saw range. It has four axes – height, tilt, rip fence and crosscut fence. These can be controlled via the ELMO 12" touch screen controls and the comprehensive range of programmes. The display depicts 90 % of all applications. A crosscut-mitre fence with automatic length compensation, two motorised flip stops and manual angle adjustment is available as an option. Switching between front and rear positions on the cross slide can be achieved without lifting the fence. The mitre angle can be adjusted by up to 47° in either position and is displayed in digital form on the screen, to an accuracy of 1/100°. The VARIO drive for infinitely variable speed adjustment (between 2 000 and 6 000 rpm.) forms an integral part of the machine. And the interface package option means the F 45 ELMO can be networked.

Equipment

F 45 ELMO IV
[supplementary to the basic version F 45]

Optional Equipment

Technical data

Sliding table cutting lengths

Maximum cutting lengths when using clamping shoe or crosscut-mitre fence. Not in conjunction with crosscut fence, stops to 2 500 mm.
Table length (mm)	2 250	3 000	3 200	3 400	3 800	4 300	5 000
Cutting length (mm) with or without scoring saw blade	2 155	2 905	3 105	3 305	3 705	3 870 (4 205*)	3 870 (4 905*)
Cutting length (mm) for F 45 ELMO IV with or without scoring saw blade	2 100	2 850	3 050	3 250	3 650	-	-
TIP-SERVO-DRIVE
Cutting length (mm) without scoring saw blade	1 840	2 590	2 790	2 990	3 390	3 870	3 870 (4 570*)
Cutting length (mm) with scoring saw blade	1 725	2 475	2 675	2 875	3 275	3 775	3 775 (4 475*)
* Possible cutting lengths without use of the crosscut fence and cross slide. Cutting lengths refer to mechanical travel, i. e. from end stop to end stop on the sliding table.

Depth of cut

without scoring saw blade
Saw Blade Diameter (mm)	250	300	315	350	400	450	500	550
Depth of cut vertical (mm)	0-50	0-75	0-82	0-100	25-125	50-150	75-175	100-200
Depth of cut at 45° (mm)	0-33	0-50	0-56	0-70	17-87	34-105	52-123	70-141

with scoring saw blade
Saw Blade Diameter (mm)	250	300	315	350	400	450¹⁾	500¹⁾	-
Depth of cut vertical (mm)	0-50	0-75	0-82	0-100	0-125	25-150	50-175	-
Depth of cut at 45° (mm)	0-33	0-50	0-56	0-70	0-87	16-105	34-123	-
¹⁾ If a scoring unit is fitted, the scoring saw blade, incl. front and back flanges, or RAPIDO must be removed.

Space requirements

Your F 45’s space requirements are as below:
A	Cutting width + 330 mm
B	Cutting width + 310 mm Cutting width + 400 mm	with manual adjustment and DIGIT X for F 45 ELMO III and F 45 ELMO IV
C	Sliding table length + 360 mm
D	Sliding table length + 290 mm
E	Crosscut-mitre fence Crosscut-mitre fence with DIGIT L Crosscut-mitre fence F 45 ELMO IV Crosscut fence up to 3 200 mm	1 970 – max. 3 635 mm 1 970 – max. 3 335 mm 2 100 – max. 3 650 mm 1 445 – max. 3 330 mm
Machine weight
depending on configuration 870 kg – 1 170 kg
Table height
910 mm

ELECTRICAL POWER REQUIREMENTS

^{ELECTRICAL POWER REQUIREMENTS 3)}
Motor (kW)	5,5	7,5	11	VARIO
Voltage(V)	380-420	380-420	380-400	380-400
Frequency (Hz)	50	50	50	50
Current (A) without/with scorer	11,5 / 13,5	15,5 / 17,5	22,5 / 24,5	11,0 / 13,0
Fuses/circuit breakers (A)	25	25	35	35
³⁾The cross section of the mains cable depends on the machine’s distance from the power source and must be determined by a qualified electrician (Power drop in the input cable ≤ 3 %). For VARIO machines: RCD protection type B, all current (AC/DC) sensitive. The minimum cross section of the mains cable for machines with VARIO motor is 4 x 4 mm². Please contact your Altendorf sales partner if your power supply does not match the requirements shown.

DUST EXTRACTION CONNECTIONS

DUST EXTRACTION CONNECTIONS
Top connection:	Ø = 80 mm
Bottom connection:	Ø = 120 mm
Pressure drop:	1 500 Pa with a total connection diameter, Ø = 140 mm
Minimum air requirement:	V_min = 1 500 m³/h at 25 m/sec.

Further information

	Operating instructions
	Brochure
	Configurator

F 45 ELMO IV: High-level CNC-technology.